FLASH
-13 %
Stock: In Stock
Model: Rod-D10
Material: Stainless steel 304 Quality: H9 Precision cutting: cutting is done by hand, so the measure may be slightly higher, but will never be less than indicated. Edges: The edges are delivered conveniently filed down. Straightness: the maximum allowed deviation is 1mm/m in rods..
2.70€ 2.35€
Ex Tax:1.94€
FLASH
-40 %
Stock: In Stock
Model: Rod-D12
Material: Stainless steel 304 Quality: H9 Precision cutting: cutting is done by hand, so the measure may be slightly higher, but will never be less than indicated. Edges: The edges are delivered conveniently filed down. Straightness: the maximum allowed deviation is 1mm/m in rods..
4.95€ 2.99€
Ex Tax:2.47€
FLASH
-21 %
Stock: In Stock
Model: Rod-D8
Material: Stainless steel 304 Quality: H9 Precision cutting: cutting is done by hand, so the measure may be slightly higher, but will never be less than indicated. Edges: The edges are delivered conveniently filed down. Straightness: the maximum allowed deviation is 1mm/m in rods..
1.90€ 1.50€
Ex Tax:1.24€
Stock: In Stock
Model: 608ZZ
Bearings 608zz standard, which are used in printers in the extruder “Greg’s wade” and its derivatives, and also used for the tensors in X-axis and Y-axis. Speed: ABEC 5 For low speed applications such as extruders, idlers or tensioners, this model is not recommended for precision applications.N..
0.27€
Ex Tax:0.22€
FLASH
-21 %
Stock: In Stock
Model: PrintedParts-Voron0.1
Parts are printed after the order.Printed parts for the Voron 0.1 Printer, developed by the team at VORON Design.Parts are printed in ABS or ASA as recommended by the community.Accent parts are printed in ABS, you can choose ABS or ASA for the main parts.This kit includes as a base the essentia..
63.50€ 49.99€
Ex Tax:41.31€
FLASH
-20 %
Stock: In Stock
Model: PrintedParts-Voron2.4-r1
Parts are printed after the order.Printed parts for the Voron 2.4 Printer, developed by the team at VORON Design.Parts are printed in ABS or ASA as recommended by the community.Accent parts are printed in ABS, you can choose ABS or ASA for the main parts.This kit includes as a base the essentia..
109.99€ 87.99€
Ex Tax:72.72€
FLASH
-68 %
Stock: In Stock
Model: Mk3 214x214
All features similar to MK2, you can also operate this board with 12 Volt or 24 Volt Heatbed with 3mm aluminum core. You can print directly on the heatbed, the glass is recommended but not mandatory The metallic side is the top print side and the black side is the bottom side. We recommend..
24.99€ 7.99€
Ex Tax:6.60€
Stock: In Stock
Model: Kapton10mm
Polyimide tape BGA, electrically insulating and heat resistant. Dimensions: 10mmx33m High heat resistance: 280°C Adhesive silicone protection without leaving any residue High dielectric strength ..
2.35€
Ex Tax:1.94€
FLASH
-20 %
Stock: In Stock
Model: LM10UU
Are used in reprap printers for the linear movement using smoth ribs of 10mm. Nominal dimensions: Outside diameter: 19mm Inside diameter: 10mm Length: 29mm 1 Piece..
0.82€ 0.66€
Ex Tax:0.55€
FLASH
-18 %
Stock: In Stock
Model: MAX31865-V2
MAX31865 V2.0 temperature detector module. This module uses the MAX31865 chip.High temperature precision.Compact and simple mounting, it uses the same connection as the motor drivers.Support connection with PT100 / PT1000, 2/3/4 wires.It uses VCCIO as part of the power supply.Supports 3.3V and 5V po..
10.90€ 8.99€
Ex Tax:7.43€
FLASH
-51 %
Stock: In Stock
Model: MK7
These precision pulleys are designed especially for the extrusion of the filament, its tiny teeth always guarantee a steady grip. Material: stainless steel ..
0.99€ 0.49€
Ex Tax:0.41€
Only a few units in stock
FLASH
-12 %
Stock: In Stock
Model: Eagle-MKS
MKS Eagle is an integrated version of Nano V3.0. Features:Cortex-M4 with FPU 32-bit, 168 MHz. Flash: 512 KB. RAM: 192KB.Compatible with UBS disk printing and TF card printing.Supports Virtual USB Device function.Integrated 5 TMC2209 driver with UART mode.Integrated snap-on drive heat sink and a..
52.50€ 45.99€
Ex Tax:38.01€