Stock: In Stock
Model: RAMPS1.6
RepRap Pololu Arduino Mega Shield or RAMPS. It is designed to connect all the electronic components required for a RepRap. The modular design includes connectors for the stepper mortos and controll electronics on a shield Arduino MEGA for easy maintenance. Ramps 1.6 is optimized and l..
10.75€
Ex Tax:8.88€
Recommended
Out of Stock
Stock: Out of Stock
Model: RAMPS1.6+
This version of the popular Ramps 3D printer electronics is a revision that integrates SPI compatibility, eliminating the need for extra wiring for the SPI pins.Main features:Compatible with SPI and SPEP / DIR, configurable through the jumpers integrated in the board.4-layer motherboard, improving o..
10.99€
Ex Tax:9.08€
-60 %
Stock: In Stock
Model: Teflón-4-1.9-red
Teflon tube with internal diameter 1.9mm, for 1.75mm filament.The inner walls of the tube are very smooth, which guarantees a high control over the flow.Due to its internal diameter of 1.9mm it is used for direct extruders, not recommended for use in bowden extruders.Features: It is made of pol..
0.60€ 0.24€
Ex Tax:0.20€
Stock: In Stock
Model: Robin-Nano
Version: 3.1Robin nano V3.1 is an upgraded version of Robin Nano V3.0, change the MCU from STM32F407VGT6 to STM32F407VET6. What is more, Robin Nano V3.1 improves the anti-interference performance, such as adding Schottky diodes to the temperature measurement circuit and MOS circuit, and adding TVS p..
41.75€
Ex Tax:34.50€
Stock: In Stock
Model: Robin-Wifi
MKS Robin WIFI is developed by Makerbase based on ESP8266 module, it is used on MKS Robin series motherboard for remote control and monitor.Features:Automatic search after power on.Repeater/pronterface remote control instead of usb.With "MKS Plugin" (developed by Makerbase for Cura), cura remote con..
7.99€
Ex Tax:6.60€
Stock: In Stock
Model: Aislante-Hotend
Rockwool Thermal insulation is used for heater block of the
Hotend, helping to maintain the temperature.
Thermal behavior
The structure of the rockwool contains dry and stable air
inside, which acts as a barrier to heat transfer characterized by its low thermal
conductivity, which i..
0.19€
Ex Tax:0.16€
Stock: In Stock
Model: HEVO-Varillas
Rod kit for the popular CoreXY HyperCube Evolution model, HEVO, if you need other lengths for the different variants, please do not hesitate to contact us.Composition:4x Rods diameter 12 length 400mm2x Rods diameter 10 length 410mm2x Rods diameter 8 length 450mmQuality:The smooth rods are calibrated..
59.99€
Ex Tax:49.58€
Stock: In Stock
Model: S2DW
Version: 1.0S2DW V1.0 is a module to compensate for printer resonances. The module meets Klipper input configuration requirements by accurately measuring resonant frequencies and reducing pressure ripple at high speeds and accelerations.Difference Between S2DW V1.0 and ADXL345 V2.0:The only differen..
10.99€
Ex Tax:9.08€
Stock: In Stock
Model: S6-fysetc
Actual Version: 2.1The S6 board is based on the STM32F446 32bit mcu has six drive sockets and supports the full range of TMC drives. They have fully extended the resources of the MCU so that you can maximize its power. They considered the possible use scenarios of 3D printers and designed a series o..
54.49€
Ex Tax:45.03€
Stock: In Stock
Model: SC10LUU
Used in 3D printers, and CNC machines, they integrate an aluminum bracket that facilitates bonding and stability.For 10mm rod1 Piece..
5.99€
Ex Tax:4.95€
Stock: In Stock
Model: SC10UU
Used in 3D printers, and CNC machines, they integrate an aluminum bracket that facilitates bonding and stability.For 10mm rod1 Piece..
2.35€
Ex Tax:1.94€
Stock: In Stock
Model: SC12LUU
Used in 3D printers, and CNC machines, they integrate an aluminum bracket that facilitates bonding and stability.For 12mm rod1 Piece..
4.75€
Ex Tax:3.93€