Only a few units in stock
-20 %
Stock: In Stock
Model: Manta-4MP
Version: 2.2Functions and application:Installed with 32-bit 64MHz ARM® Cortex-M0+ STM32G0BORE chip, more stable and faster.Designed with the same connector with Raspberry Pi, giving you a confident connection with all versions of CM4, definitely, CB1. Also, a screw-reinforced installation is also av..
69.99€ 55.99€
Ex Tax:46.27€
Only a few units in stock
-22 %
Stock: In Stock
Model: Manta-8MP
Version: 1.1Functions and application:Installed with 32-bit 64MHz ARM® Cortex-M0+ STM32G0B1VET6 chip, more stable and faster.Designed with the same connector with Raspberry Pi, giving you a confident connection with all versions of CM4,definitely, CB1. Also, a screw-reinforced installation is also a..
89.99€ 69.99€
Ex Tax:57.84€
Stock: In Stock
Model: Manta-8MP-V2
Version: 2Functions and application:Installed with 32-bit 64MHz ARM® Cortex-M0+ STM32H723ZET6 550MHzchip, more stable and faster.Designed with the same connector with Raspberry Pi, giving you a confident connection with all versions of CM4,definitely, CB1. Also, a screw-reinforced installation is al..
75.99€
Ex Tax:62.80€
-29 %
Out of Stock
Stock: Out of Stock
Model: MegaCompatible
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 .It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a rese..
17.99€ 12.75€
Ex Tax:10.54€
Recommended
-38 %
Out of Stock
Stock: Out of Stock
Model: Mega 2560 R3 (Compatible) 16u2
Mega 2560 R3 (Compatible) 16u2This is a clone of quality, not only just aesthetically , also uses the same chip USB connection so it is 100 % compatible with the original drivers.It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ..
24.99€ 15.45€
Ex Tax:12.77€
Stock: In Stock
Model: 3MOS-MKS
MKS 3MOS is a connection fan module. The module integrates 3 MOS control outputs, and its pins and dimensions are compatible with pluggable motor drive slots. It can be used directly by connecting to the drive slot and simply configuring the pin file. Suitable for motherboards with more than 5 axis ..
2.70€
Ex Tax:2.23€
Stock: In Stock
Model: Eagle-MKS
MKS Eagle is an integrated version of Nano V3.0. Features:Cortex-M4 with FPU 32-bit, 168 MHz. Flash: 512 KB. RAM: 192KB.Compatible with UBS disk printing and TF card printing.Supports Virtual USB Device function.Integrated 5 TMC2209 driver with UART mode.Integrated snap-on drive heat sink and a..
52.50€
Ex Tax:43.39€
Stock: In Stock
Model: Monster8-V2-MKS
MKS Monster8 V2 is an upgraded version of Monster8 V1. On the basis of retaining the functions of the original V1, has added independent DV5V for the Raspberry Pi, has reserved Robin WIFI interface for RRF firmware, added more protection circuits and reserved more functional interfaces.Specs:MCU: ST..
46.99€
Ex Tax:38.83€
Stock: In Stock
Model: MKS-PI
Version: 1.1MKS PI is a high-end microcomputer board designed by Makerbase to replace the Raspberry Pi for the convenience of 3D printing users to use the Klipper firmware. The size, mounting holes, and most interface locations are also compatible with Raspberry Pi 3B. In terms of hardware, MKS PI h..
48.50€
Ex Tax:40.08€
-13 %
Out of Stock
Stock: Out of Stock
Model: Sgen_L-MKS
Version V2.0MKS SGEN_L V2.0 es una potente placa de control de impresora 3D de 32 bits.CPU LPC1769 120MHZ de alta frecuencia y más velocidad de procesamientoEEPROM 4KB integradaConexión para eje Z dualCompatible con 12 V y 24VAdmite el modo UART, SPI y STEP / DIR.For more information click here...
38.00€ 33.00€
Ex Tax:27.27€
Stock: In Stock
Model: SKIPR
Version: 1.0MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the STM32F407VET6 MCU responsible for executing specific machine actions. It meets the use of most 3D printers.Features and advantages:SOC uses Rockchip's..
79.99€
Ex Tax:66.11€
Stock: In Stock
Model: dual-axis-module
Simple complement to connect two motors in parallel, usually used with Z axis, but can be used with any other axis. Recommended to connect two equal motors so that the current is distributed equally between them.Use with small or medium sized 3D printers, avoid large sized motors.Content:1x Boa..
1.25€
Ex Tax:1.03€