Stock: In Stock
Model: dual-axis-module
Simple complement to connect two motors in parallel, usually used with Z axis, but can be used with any other axis. Recommended to connect two equal motors so that the current is distributed equally between them.Use with small or medium sized 3D printers, avoid large sized motors.Content:1x Boa..
1.25€
Ex Tax:1.03€
Out of Stock
Stock: Out of Stock
Model: mosfet-module
It can control the current of devices or accessories, such as fans, or additional lights.Signal Voltage: 3.3V, 5VOutput voltage: 0-24 VRated current: <5A (To overcome 1A it needs additional dissipation)Size: 33 x 25mm
1 Piece..
1.75€
Ex Tax:1.45€
Stock: In Stock
Model: MR105zz Bearing
Bearings 605zz standard are used in printers for Direct Drive extruders or axis movement. Nominal dimensions: Inside diameter: 5mm Outside diameter: 10mm Thickness: 4mm 1 Piece ..
0.29€
Ex Tax:0.24€
Stock: In Stock
Model: 17HS4401s-T8x8-300MM
Precision motor T8x8
trapezoidal screw integral with the shaft. By eliminating the need
for flexible couplings problems of shaft misalignment are eliminated
and results in a more compact solution. Specifications:
Shaft length: 300mm
Step : 8mm 1/32
Controller re..
23.99€
Ex Tax:19.83€
Stock: In Stock
Model: 17HS4401s-T8x8-310MM
Precision motor T8x8
trapezoidal screw integral with the shaft. By eliminating the need
for flexible couplings problems of shaft misalignment are eliminated
and results in a more compact solution. Specifications:
Shaft length: 310mm
Step : 8mm 1/32
Controller re..
23.99€
Ex Tax:19.83€
Out of Stock
Stock: Out of Stock
Model: 17HS4401s-T8x8-350MM
Precision motor T8x8
trapezoidal screw integral with the shaft. By eliminating the need
for flexible couplings problems of shaft misalignment are eliminated
and results in a more compact solution. Specifications:
Shaft length: 350mm
Step : 8mm 1/32
Controller re..
25.50€
Ex Tax:21.07€
Stock: In Stock
Model: 17HS4401S-PG518
Precition motor with great power, its 5.18 to 1 relation multiplies the motor strength, which makes it ideal for bowden extruders, or any other system that needs big strength and precisition at slow turn speeds. The number of complete steps per revolution is 1036.Specifications: ..
34.99€
Ex Tax:28.92€
FLASH
-26 %
Stock: In Stock
Model: 36HS1718
Features:Nema14 motor, small in size, light in weight and high in quality.High temperature resistant.Long service life, up to 30,000 hours.Step Angle: 1.8±5%/StepCurrent: 1.88A/PHASENumber of teeth: 10 teethWeight: 83gSize: about 51x36x23mmLead wire length: 4CM/1.57inExtension cable: 70cm1 piece&nbs..
13.50€ 9.99€
Ex Tax:8.26€
Stock: In Stock
Model: 17HS2408
Features: Each motor includes 1 meter of wire with dupont connector at its end. Nominal electrical specifications:ModelStep Angle (deg)Motor Length (mm)Rated Current (A)Phase resistence (ohm)Phase inductance (mH)Holding Torque (N·cm min)Detent Torque (N·cm max)Rotor Inercia (g·cm2)Number o..
8.10€
Ex Tax:6.69€
Stock: In Stock
Model: 17HS3401
Features:17HS3401: Compact Size, ideal for applications where you need lightweight, as mobile extruders, or other cases that works with low loads as CNC lasers, plotters and others. Each motor includes 1 meter of wire with dupont connector at its end. The shaft motor is D type, which eases..
8.25€
Ex Tax:6.82€
Stock: In Stock
Model: 17HS4401
Features:17HS4401: Compact and powerful, ideal for 3D printers in medium size, and also for small CNC machines and robotics in general. This one is the most used size. Each motor includes 1 meter of wire with dupont connector at its end. The shaft motor is D type, which eases the use of pu..
9.35€
Ex Tax:7.73€
Stock: In Stock
Model: 17HS4401s-09
Features:17HS4401s-09 - 42HS40-0.9 - 42-40 0.9: Compact and powerful, ideal for 3D printers in medium size, and also for small CNC machines and robotics in general. This one is the most used size.Step Angle: 0.9º. Half conventinal stepper motor, which give double precision.Low noise, low vibration, ..
13.65€
Ex Tax:11.28€